rockchip启动的log

DDR Version 1.27 20211018
In
channel 0
CS = 0
MR0=0x18
MR4=0x1
MR5=0x1
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
CS = 1
MR0=0x18
MR4=0x1
MR5=0x1
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
channel 1
CS = 0
MR0=0x18
MR4=0x1
MR5=0x1
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
CS = 1
MR0=0x18
MR4=0x1
MR5=0x1
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
channel 0 training pass!
channel 1 training pass!
change freq to 416MHz 0,1
Channel 0: LPDDR4,416MHz
Bus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=16 Size=2048MB
Channel 1: LPDDR4,416MHz
Bus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=16 Size=2048MB
256B stride
channel 0
CS = 0
MR0=0x18
MR4=0x1
MR5=0x1
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
CS = 1
MR0=0x18
MR4=0x1
MR5=0x1
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
channel 1
CS = 0
MR0=0x18
MR4=0x1
MR5=0x1
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
CS = 1
MR0=0x18
MR4=0x1
MR5=0x1
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0x0
channel 0 training pass!
channel 1 training pass!
channel 0, cs 0, advanced training done
channel 0, cs 1, advanced training done
channel 1, cs 0, advanced training done
channel 1, cs 1, advanced training done
change freq to 856MHz 1,0
ch 0 ddrconfig = 0x101, ddrsize = 0x2020
ch 1 ddrconfig = 0x101, ddrsize = 0x2020
pmugrf_os_reg[2] = 0x3AA1FAA1, stride = 0xD
ddr_set_rate to 328MHZ
ddr_set_rate to 666MHZ
ddr_set_rate to 416MHZ, ctl_index 0
ddr_set_rate to 856MHZ, ctl_index 1
support 416 856 328 666 MHz, current 856MHz
OUT
Boot1 Release Time: May 29 2020 17:36:36, version: 1.26
CPUId = 0x0
ChipType = 0x10, 346
mmc: ERROR: SDHCI ERR:cmd:0x102,stat:0x18000
mmc: ERROR: Card did not respond to voltage select!
emmc reinit
mmc: ERROR: SDHCI ERR:cmd:0x102,stat:0x18000
mmc: ERROR: Card did not respond to voltage select!
emmc reinit
mmc: ERROR: SDHCI ERR:cmd:0x102,stat:0x18000
mmc: ERROR: Card did not respond to voltage select!
SdmmcInit=2 1
mmc0:cmd5,20
SdmmcInit=0 0
BootCapSize=0
UserCapSize=30436MB
FwPartOffset=2000 , 0
StorageInit ok = 56247
SecureMode = 0
SecureInit read PBA: 0x4
SecureInit read PBA: 0x404
SecureInit read PBA: 0x804
SecureInit read PBA: 0xc04
SecureInit read PBA: 0x1004
SecureInit read PBA: 0x1404
SecureInit read PBA: 0x1804
SecureInit read PBA: 0x1c04
SecureInit ret = 0, SecureMode = 0
atags_set_bootdev: ret:(0)
GPT part: 0, name: loader1, start:0x40, size:0x1f40
GPT part: 1, name: loader2, start:0x4000, size:0x2000
GPT part: 2, name: trust, start:0x6000, size:0x2000
GPT part: 3, name: boot, start:0x8000, size:0x38000
GPT part: 4, name: rootfs, start:0x40000, size:0x3b323df
no find partition:uboot.
Trust Addr:0x4000, 0x58334c42
No find bl30.bin
Load uboot, ReadLba = 2000
Load OK, addr=0x200000, size=0xc0648
RunBL31 0x40000 @ 208484 us
NOTICE: BL31: v1.3(release):845ee93
NOTICE: BL31: Built : 15:51:11, Jul 22 2020
NOTICE: BL31: Rockchip release version: v1.1
INFO: GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3
INFO: Using opteed sec cpu_context!
INFO: boot cpu mask: 0
INFO: plat_rockchip_pmu_init(1196): pd status 3e
INFO: BL31: Initializing runtime services
INFO: BL31: Initializing BL32
INF [0x0] TEE-CORE:init_primary_helper:337: Initializing (1.1.0-278-gef70f120a #zhangzj #9 Fri Sep 17 09:39:24 UTC 2021 aarch64)

INF [0x0] TEE-CORE:init_primary_helper:338: Release version: 1.2

INF [0x0] TEE-CORE:init_teecore:83: teecore inits done
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x200000
INFO: SPSR = 0x3c9

U-Boot 2017.09-gef1dd65004-220629-dirty #root (Oct 21 2022 – 15:51:55 +0800)

Model: Firefly-RK3399 Board
PreSerial: 2, raw, 0xff1a0000
DRAM: 3.8 GiB
Sysmem: init
Relocation Offset: f7cfc000
Relocation fdt: f5ee55e8 – f5ef2cf8
CR: M/C/I
I2c0 speed: 400000Hz
PMIC: RK808
vdd_center 900000 uV
vdd_cpu_l 900000 uV
vdd_log init 950000 uV
*** Warning – No MMC card found, using default environment

MMC: dwmmc@fe320000: 1, sdhci@fe330000: 0
In: serial
Out: serial
Err: serial
Model: Firefly-RK3399 Board
switch to partitions #0, OK
mmc1 is current device
Found IDB in SDcard
Bootdev(atags): mmc 1
MMC1: Legacy, 52Mhz
PartType: EFI
No misc partition
boot mode: None
CLK: (uboot. arml: enter 400000 KHz, init 816000 KHz, kernel 0N/A)
CLK: (uboot. armb: enter 24000 KHz, init 816000 KHz, kernel 0N/A)
aplll 816000 KHz
apllb 816000 KHz
dpll 856000 KHz
cpll 24000 KHz
gpll 800000 KHz
npll 600000 KHz
vpll 24000 KHz
aclk_perihp 133333 KHz
hclk_perihp 66666 KHz
pclk_perihp 33333 KHz
aclk_perilp0 266666 KHz
hclk_perilp0 88888 KHz
pclk_perilp0 44444 KHz
hclk_perilp1 100000 KHz
pclk_perilp1 50000 KHz
No misc partition
Net: eth0: ethernet@fe300000
Hit key to stop autoboot(‘CTRL+C’): 0
Could not find misc partition
ANDROID: reboot reason: “(none)”
No valid android hdr
Android image load failed
Android boot failed, error -1.
Unknown command ‘boot_fit’ – try ‘help’

Booting Rockchip Format Image

Could not find kernel partition, ret=-1
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:4…
Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinux.conf
182 bytes read in 8 ms (21.5 KiB/s)
1: rockchip-kernel-4.4
Retrieving file: /Image
19212296 bytes read in 827 ms (22.2 MiB/s)
append: earlycon=uart8250,mmio32,0xff1a0000 root=PARTUUID=B921B045-1D rootwait rootfstype=ext4 init=/sbin/init
Retrieving file: /rk3399.dtb
100101 bytes read in 9 ms (10.6 MiB/s)
Fdt Ramdisk skip relocation
No misc partition

Flattened Device Tree blob at 0x08300000

Booting using the fdt blob at 0x08300000
‘reserved-memory’ ramoops@110000: addr=110000 size=f0000
Using Device Tree in place at 0000000008300000, end 000000000831b704
Adding bank: 0x00200000 – 0x08400000 (size: 0x08200000)
Adding bank: 0x0a200000 – 0xf8000000 (size: 0xede00000)
Total: 3504.438 ms

Starting kernel …

[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.4.194 (root@rtlinux) (gcc version 9.4.0 (Ubuntu 9.4.0-1ubuntu1~20.04.1) ) #2 SMP Fri Oct 21 11:12:16 CST 2022
[ 0.000000] Boot CPU: AArch64 Processor [410fd034]
[ 0.000000] earlycon: Early serial console at MMIO32 0xff1a0000 (options ‘’)
[ 0.000000] bootconsole [uart0] enabled
[ 0.000000] Reserved memory: failed to reserve memory for node ‘drm-logo@00000000’: base 0x0000000000000000, size 0 MiB
[ 0.000000] cma: Reserved 16 MiB at 0x00000000f7000000
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: Trusted OS migration not required
[ 0.000000] PERCPU: Embedded 21 pages/cpu @ffffffc0f6ed2000 s45864 r8192 d31960 u86016
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: enabling workaround for ARM erratum 845719
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 991752
[ 0.000000] Kernel command line: earlycon=uart8250,mmio32,0xff1a0000 root=PARTUUID=B921B045-1D rootwait rootfstype=ext4 init=/sbin/init rw swiotlb=1 console=ttyFIQ0 coherent_pool=1m
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] software IO TLB: mapped [mem 0xf6e8a000-0xf6eca000] (0MB)
[ 0.000000] Memory: 3921360K/4030464K available (10174K kernel code, 1610K rwdata, 5928K rodata, 1024K init, 617K bss, 92720K reserved, 16384K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] modules : 0xffffff8000000000 – 0xffffff8008000000 ( 128 MB)
[ 0.000000] vmalloc : 0xffffff8008000000 – 0xffffffbdbfff0000 ( 246 GB)
[ 0.000000] .init : 0xffffff8009040000 – 0xffffff8009140000 ( 1024 KB)
[ 0.000000] .text : 0xffffff8008080000 – 0xffffff8008a70000 ( 10176 KB)
[ 0.000000] .rodata : 0xffffff8008a70000 – 0xffffff8009040000 ( 5952 KB)
[ 0.000000] .data : 0xffffff8009140000 – 0xffffff80092d2808 ( 1611 KB)
[ 0.000000] vmemmap : 0xffffffbdc0000000 – 0xffffffbfc0000000 ( 8 GB maximum)
[ 0.000000] 0xffffffbdc0008000 – 0xffffffbdc3e00000 ( 61 MB actual)
[ 0.000000] fixed : 0xffffffbffe7fb000 – 0xffffffbffec00000 ( 4116 KB)
[ 0.000000] PCI I/O : 0xffffffbffee00000 – 0xffffffbfffe00000 ( 16 MB)
[ 0.000000] memory : 0xffffffc000200000 – 0xffffffc0f8000000 ( 3966 MB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 64.
[ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=6.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=6
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] ITS: /interrupt-controller@fee00000/interrupt-controller@fee20000
[ 0.000000] ITS: allocated 65536 Devices @a280000 (psz 64K, shr 0)
[ 0.000000] ITS: using cache flushing for cmd queue
[ 0.000000] GIC: using LPI property table @0x000000000a210000
[ 0.000000] ITS: Allocated 1792 chunks for LPIs
[ 0.000000] CPU0: found redistributor 0 region 0:0x00000000fef00000
[ 0.000000] CPU0: using LPI pending table @0x000000000a220000
[ 0.000000] GIC: using cache flushing for LPI property table
[ 0.000000] GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpus/cpu@1[1] /cpus/cpu@2[2] /cpus/cpu@3[3] }
[ 0.000000] GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /cpus/cpu@101[5] }
[ 0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop0_frac as parent of dclk_vop0, rate changes may not work
[ 0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop1_frac as parent of dclk_vop1, rate changes may not work
[ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.002154] Console: colour dummy device 80×25
[ 0.002594] Calibrating delay loop (skipped), value calculated using timer frequency… 48.00 BogoMIPS (lpj=24000)
[ 0.003580] pid_max: default: 32768 minimum: 301
[ 0.004155] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.004806] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.006185] Initializing cgroup subsys devices
[ 0.006618] Initializing cgroup subsys freezer
[ 0.007078] ftrace: allocating 38122 entries in 149 pages
[ 0.104483] sched-energy: Sched-energy-costs installed from DT
[ 0.105049] CPU0: update cpu_capacity 401
[ 0.105493] ASID allocator initialised with 32768 entries
[ 0.108999] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
[ 0.110318] Platform MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
[ 0.112561] Detected VIPT I-cache on CPU1
[ 0.112598] CPU1: found redistributor 1 region 0:0x00000000fef20000
[ 0.112628] CPU1: using LPI pending table @0x00000000f1ca0000
[ 0.112681] CPU1: update cpu_capacity 401
[ 0.112685] CPU1: Booted secondary processor [410fd034]
[ 0.113453] Detected VIPT I-cache on CPU2
[ 0.113486] CPU2: found redistributor 2 region 0:0x00000000fef40000
[ 0.113515] CPU2: using LPI pending table @0x00000000f1cd0000
[ 0.113563] CPU2: update cpu_capacity 401
[ 0.113567] CPU2: Booted secondary processor [410fd034]
[ 0.114300] Detected VIPT I-cache on CPU3
[ 0.114331] CPU3: found redistributor 3 region 0:0x00000000fef60000
[ 0.114360] CPU3: using LPI pending table @0x00000000f1d10000
[ 0.114405] CPU3: update cpu_capacity 401
[ 0.114409] CPU3: Booted secondary processor [410fd034]
[ 0.115173] Detected PIPT I-cache on CPU4
[ 0.115197] CPU4: found redistributor 100 region 0:0x00000000fef80000
[ 0.115232] CPU4: using LPI pending table @0x00000000f1d50000
[ 0.115267] CPU4: update cpu_capacity 1024
[ 0.115270] CPU4: Booted secondary processor [410fd082]
[ 0.115945] Detected PIPT I-cache on CPU5
[ 0.115970] CPU5: found redistributor 101 region 0:0x00000000fefa0000
[ 0.116005] CPU5: using LPI pending table @0x00000000f1d80000
[ 0.116039] CPU5: update cpu_capacity 1024
[ 0.116042] CPU5: Booted secondary processor [410fd082]
[ 0.116134] Brought up 6 CPUs
[ 0.128475] SMP: Total of 6 processors activated.
[ 0.128925] CPU features: detected feature: GIC system register CPU interface
[ 0.129613] CPU features: detected feature: 32-bit EL0 Support
[ 0.130170] CPU: All CPU(s) started at EL2
[ 0.130598] alternatives: patching kernel code
[ 0.132388] devtmpfs: initialized
[ 0.155808] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[ 0.156764] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 0.158125] pinctrl core: initialized pinctrl subsystem
[ 0.160257] Failed to find legacy iommu devices
[ 0.161030] NET: Registered protocol family 16
[ 0.165501] cpuidle: using governor ladder
[ 0.170518] cpuidle: using governor menu
[ 0.170908] Registered FIQ tty driver
[ 0.171444] vdso: 2 pages (1 code @ ffffff8008a76000, 1 data @ ffffff8009144000)
[ 0.172178] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.173764] DMA: preallocated 1024 KiB pool for atomic allocations
[ 0.196600] console [pstore-1] enabled
[ 0.196963] pstore: Registered ramoops as persistent store backend
[ 0.197561] ramoops: attached 0xf0000@0x110000, ecc: 0/0
[ 0.200631] console [ttyFIQ0] enabled
[ 0.200631] console [ttyFIQ0] enabled
[ 0.201308] bootconsole [uart0] disabled
[ 0.201308] bootconsole [uart0] disabled
[ 0.202243] Registered fiq debugger ttyFIQ0
[ 0.217562] iommu: Adding device ff650000.vpu_service to group 0
[ 0.218170] iommu: Adding device ff660000.rkvdec to group 1
[ 0.218782] iommu: Adding device ff8f0000.vop to group 2
[ 0.219342] iommu: Adding device ff900000.vop to group 3
[ 0.219946] iommu: Adding device ff910000.cif_isp to group 4
[ 0.220885] rk_iommu ff650800.iommu: can’t get sclk
[ 0.221559] rk_iommu ff660480.iommu: can’t get sclk
[ 0.222205] rk_iommu ff8f3f00.iommu: can’t get sclk
[ 0.222793] rk_iommu ff903f00.iommu: can’t get sclk
[ 0.223399] rk_iommu ff914000.iommu: can’t get sclk
[ 0.224183] SCSI subsystem initialized
[ 0.224700] usbcore: registered new interface driver usbfs
[ 0.225224] usbcore: registered new interface driver hub
[ 0.225784] usbcore: registered new device driver usb
[ 0.226300] media: Linux media interface: v0.10
[ 0.226753] Linux video capture interface: v2.00
[ 0.227234] pps_core: LinuxPPS API ver. 1 registered
[ 0.227676] pps_core: Software ver. 5.3.6 – Copyright 2005-2007 Rodolfo Giometti giometti@linux.it
[ 0.228508] PTP clock support registered
[ 0.230169] Advanced Linux Sound Architecture Driver Initialized.
[ 0.231181] Bluetooth: Core ver 2.21
[ 0.231528] NET: Registered protocol family 31
[ 0.231934] Bluetooth: HCI device and connection manager initialized
[ 0.232507] Bluetooth: HCI socket layer initialized
[ 0.232949] Bluetooth: L2CAP socket layer initialized
[ 0.233423] Bluetooth: SCO socket layer initialized
[ 0.234451] rockchip-cpuinfo cpuinfo: Serial : f68a90cd184ce63a
[ 0.235496] clocksource: Switched to clocksource arch_sys_counter
[ 0.285667] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
[ 0.286586] NET: Registered protocol family 2
[ 0.287376] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.288286] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes)
[ 0.289713] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.290397] UDP hash table entries: 2048 (order: 5, 196608 bytes)
[ 0.291105] UDP-Lite hash table entries: 2048 (order: 5, 196608 bytes)
[ 0.292069] NET: Registered protocol family 1
[ 0.292749] RPC: Registered named UNIX socket transport module.
[ 0.293274] RPC: Registered udp transport module.
[ 0.293708] RPC: Registered tcp transport module.
[ 0.294128] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.295785] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[ 0.296598] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
[ 0.300377] Initialise system trusted keyring
[ 0.308930] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.310221] NFS: Registering the id_resolver key type
[ 0.310711] Key type id_resolver registered
[ 0.311086] Key type id_legacy registered
[ 0.311526] ntfs: driver 2.1.32 [Flags: R/O].
[ 0.312138] fuse init (API version 7.23)
[ 0.312862] SGI XFS with security attributes, no debug enabled
[ 0.318283] NET: Registered protocol family 38
[ 0.318709] Key type asymmetric registered
[ 0.319076] Asymmetric key parser ‘x509’ registered
[ 0.319669] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[ 0.320323] io scheduler noop registered
[ 0.320688] io scheduler deadline registered
[ 0.321194] io scheduler cfq registered (default)
[ 0.323256] phy phy-ff770000.syscon:usb2-phy@e460.1: Failed to get VBUS supply regulator
[ 0.329564] rockchip-pcie f8000000.pcie: no vpcie3v3 regulator found
[ 0.330159] rockchip-pcie f8000000.pcie: no vpcie1v8 regulator found
[ 0.330765] rockchip-pcie f8000000.pcie: no vpcie0v9 regulator found
[ 0.331333] rockchip-pcie f8000000.pcie: missing “memory-region” property
[ 0.332058] PCI host bridge /pcie@f8000000 ranges:
[ 0.332522] MEM 0xfa000000…0xfbdfffff -> 0xfa000000
[ 0.332980] IO 0xfbe00000…0xfbefffff -> 0xfbe00000
[ 0.387884] rockchip-pcie f8000000.pcie: PCI host bridge to bus 0000:00
[ 0.388469] pci_bus 0000:00: root bus resource [bus 00-1f]
[ 0.388976] pci_bus 0000:00: root bus resource [mem 0xfa000000-0xfbdfffff]
[ 0.389593] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0xfbe00000-0xfbefffff])
[ 0.390819] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.391857] pci 0000:01:00.0: reg 0x10: initial BAR value 0x00000000 invalid
[ 0.394582] pci 0000:00:00.0: BAR 8: assigned [mem 0xfa000000-0xfa0fffff]
[ 0.395191] pci 0000:01:00.0: BAR 4: assigned [mem 0xfa000000-0xfa003fff 64bit]
[ 0.395891] pci 0000:01:00.0: BAR 2: assigned [mem 0xfa004000-0xfa004fff 64bit]
[ 0.396587] pci 0000:01:00.0: BAR 0: no space for [io size 0x0100]
[ 0.397145] pci 0000:01:00.0: BAR 0: failed to assign [io size 0x0100]
[ 0.397737] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.398185] pci 0000:00:00.0: bridge window [mem 0xfa000000-0xfa0fffff]
[ 0.398845] pcieport 0000:00:00.0: enabling device (0000 -> 0002)
[ 0.399622] pcieport 0000:00:00.0: Signaling PME through PCIe PME interrupt
[ 0.400238] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
[ 0.401672] Module initialized.
[ 0.402243] rk-vcodec ff650000.vpu_service: no regulator for vcodec
[ 0.403071] rk-vcodec ff650000.vpu_service: probe device
[ 0.403769] rk-vcodec ff650000.vpu_service: drm allocator with mmu enabled
[ 0.404914] rk-vcodec ff650000.vpu_service: could not find power_model node
[ 0.405549] rk-vcodec ff650000.vpu_service: init success
[ 0.406254] rk-vcodec ff660000.rkvdec: no regulator for vcodec
[ 0.407194] rk-vcodec ff660000.rkvdec: probe device
[ 0.407828] rk-vcodec ff660000.rkvdec: drm allocator with mmu enabled
[ 0.408757] rk-vcodec ff660000.rkvdec: could not find power_model node
[ 0.409339] rk-vcodec ff660000.rkvdec: init success
[ 0.411508] dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-241330
[ 0.412185] dma-pl330 ff6d0000.dma-controller: DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12
[ 0.414464] dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-241330
[ 0.415152] dma-pl330 ff6e0000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
[ 0.417006] rockchip-system-monitor rockchip-system-monitor: system monitor probe
[ 0.418884] Serial: 8250/16550 driver, 5 ports, IRQ sharing disabled
[ 0.420072] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 36, base_baud = 1500000) is a 16550A
[ 0.421952] [drm] Initialized drm 1.1.0 20060810
[ 0.425957] [drm] Rockchip DRM driver version: v1.0.1
[ 0.426742] rockchip-drm display-subsystem: dmc is disabled
[ 0.427542] rockchip-vop ff900000.vop: missing rockchip,grf property
[ 0.428360] rockchip-drm display-subsystem: bound ff900000.vop (ops 0xffffff8008b16640)
[ 0.429118] rockchip-vop ff8f0000.vop: missing rockchip,grf property
[ 0.429872] rockchip-drm display-subsystem: bound ff8f0000.vop (ops 0xffffff8008b16640)
[ 0.430841] i2c i2c-9: of_i2c: modalias failure on /hdmi@ff940000/ports
[ 0.431440] dwhdmi-rockchip ff940000.hdmi: registered DesignWare HDMI I2C bus driver
[ 0.432230] dwhdmi-rockchip ff940000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
[ 0.433898] rockchip-drm display-subsystem: bound ff940000.hdmi (ops 0xffffff8008b0a9b8)
[ 0.434629] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 0.435219] [drm] No driver support for vblank timestamp query.
[ 0.435933] rockchip-drm display-subsystem: failed to parse loader memory
[ 0.436566] rockchip-drm display-subsystem: No connectors reported connected with modes
[ 0.437298] [drm] Cannot find any crtc or sizes – going 1024×768
[ 0.441906] rockchip-drm display-subsystem: fb0: frame buffer device
[ 0.450038] mali ff9a0000.gpu: Failed to get regulator
[ 0.450512] mali ff9a0000.gpu: Power control initialization failed
[ 0.451436] Unable to detect cache hierarchy for CPU 0
[ 0.452616] brd: module loaded
[ 0.457978] loop: module loaded
[ 0.458789] zram: Added device: zram0
[ 0.459430] lkdtm: No crash points registered, enable through debugfs
[ 0.461884] rk_gmac-dwmac fe300000.ethernet: clock input or output? (input).
[ 0.462527] rk_gmac-dwmac fe300000.ethernet: TX delay(0x28).
[ 0.463030] rk_gmac-dwmac fe300000.ethernet: RX delay(0x11).
[ 0.463554] rk_gmac-dwmac fe300000.ethernet: integrated PHY? (no).
[ 0.464267] rk_gmac-dwmac fe300000.ethernet: cannot get clock clk_mac_speed
[ 0.464892] rk_gmac-dwmac fe300000.ethernet: clock input from PHY
[ 0.470445] rk_gmac-dwmac fe300000.ethernet: init for RGMII
[ 0.471067] stmmac – user ID: 0x10, Synopsys ID: 0x35
[ 0.471531] Ring mode enabled
[ 0.471813] DMA HW capability register supported
[ 0.472218] Normal descriptors
[ 0.472532] RX Checksum Offload Engine supported (type 2)
[ 0.473018] TX Checksum insertion supported
[ 0.473400] Wake-Up On Lan supported
[ 0.473768] Enable RX Mitigation via HW Watchdog Timer
[ 0.538634] libphy: stmmac: probed
[ 0.538945] eth%d: PHY ID 001cc915 at 0 IRQ POLL (stmmac-0:00) active
[ 0.539521] eth%d: PHY ID 001cc915 at 1 IRQ POLL (stmmac-0:01)
[ 0.541329] usbcore: registered new interface driver rndis_wlan
[ 0.542016] Rockchip WiFi SYS interface (V1.00) …
[ 0.542544] usbcore: registered new interface driver rtl8150
[ 0.543078] usbcore: registered new interface driver r8152
[ 0.543626] usbcore: registered new interface driver asix
[ 0.544135] usbcore: registered new interface driver ax88179_178a
[ 0.544727] usbcore: registered new interface driver cdc_ether
[ 0.545281] usbcore: registered new interface driver rndis_host
[ 0.545881] usbcore: registered new interface driver cdc_ncm
[ 0.546414] usbcore: registered new interface driver cdc_mbim
[ 0.548304] rockchip-dwc3 usb0: failed to get drvdata dwc3
[ 0.553630] rockchip-dwc3 usb1: fail to get drvdata hcd
[ 0.555328] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[ 0.555940] ehci-pci: EHCI PCI platform driver
[ 0.556390] ehci-platform: EHCI generic platform driver
[ 0.560681] ehci-platform fe3c0000.usb: EHCI Host Controller
[ 0.561344] ehci-platform fe3c0000.usb: new USB bus registered, assigned bus number 1
[ 0.562211] ehci-platform fe3c0000.usb: irq 30, io mem 0xfe3c0000
[ 0.568517] ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00
[ 0.569210] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.569832] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.570470] usb usb1: Product: EHCI Host Controller
[ 0.570912] usb usb1: Manufacturer: Linux 4.4.194 ehci_hcd
[ 0.571401] usb usb1: SerialNumber: fe3c0000.usb
[ 0.572272] hub 1-0:1.0: USB hub found
[ 0.572650] hub 1-0:1.0: 1 port detected
[ 0.573573] ohci_hcd: USB 1.1 ‘Open’ Host Controller (OHCI) Driver
[ 0.574133] ohci-platform: OHCI generic platform driver
[ 0.575096] ohci-platform fe3e0000.usb: Generic Platform OHCI controller
[ 0.575858] ohci-platform fe3e0000.usb: new USB bus registered, assigned bus number 2
[ 0.576680] ohci-platform fe3e0000.usb: irq 31, io mem 0xfe3e0000
[ 0.631661] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.632267] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.632918] usb usb2: Product: Generic Platform OHCI controller
[ 0.633442] usb usb2: Manufacturer: Linux 4.4.194 ohci_hcd
[ 0.633940] usb usb2: SerialNumber: fe3e0000.usb
[ 0.634831] hub 2-0:1.0: USB hub found
[ 0.635194] hub 2-0:1.0: 1 port detected
[ 0.636526] usbcore: registered new interface driver cdc_acm
[ 0.637027] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 0.637781] usbcore: registered new interface driver cdc_wdm
[ 0.638320] usbcore: registered new interface driver uas
[ 0.638888] usbcore: registered new interface driver usb-storage
[ 0.639502] usbcore: registered new interface driver usbserial
[ 0.640052] usbcore: registered new interface driver usbserial_generic
[ 0.640667] usbserial: USB Serial support registered for generic
[ 0.641235] usbcore: registered new interface driver cp210x
[ 0.641768] usbserial: USB Serial support registered for cp210x
[ 0.642339] usbcore: registered new interface driver ftdi_sio
[ 0.642883] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 0.643623] usbcore: registered new interface driver keyspan
[ 0.644143] usbserial: USB Serial support registered for Keyspan – (without firmware)
[ 0.644866] usbserial: USB Serial support registered for Keyspan 1 port adapter
[ 0.645545] usbserial: USB Serial support registered for Keyspan 2 port adapter
[ 0.646215] usbserial: USB Serial support registered for Keyspan 4 port adapter
[ 0.646911] usbcore: registered new interface driver option
[ 0.647431] usbserial: USB Serial support registered for GSM modem (1-port)
[ 0.648161] usbcore: registered new interface driver oti6858
[ 0.648694] usbserial: USB Serial support registered for oti6858
[ 0.649262] usbcore: registered new interface driver pl2303
[ 0.649793] usbserial: USB Serial support registered for pl2303
[ 0.650356] usbcore: registered new interface driver qcserial
[ 0.650901] usbserial: USB Serial support registered for Qualcomm USB modem
[ 0.651574] usbcore: registered new interface driver sierra
[ 0.652093] usbserial: USB Serial support registered for Sierra USB modem
[ 0.653829] usbcore: registered new interface driver usbtouchscreen
[ 0.655178] i2c /dev entries driver
[ 0.657093] rk808 0-001b: Pmic Chip id: 0x0
[ 0.660556] rk808-regulator rk808-regulator: there is no dvs0 gpio
[ 0.661158] rk808-regulator rk808-regulator: there is no dvs1 gpio
[ 0.661812] DCDC_REG1: supplied by vcc3v3_sys
[ 0.662981] DCDC_REG2: supplied by vcc3v3_sys
[ 0.663966] DCDC_REG3: supplied by vcc3v3_sys
[ 0.664671] DCDC_REG4: supplied by vcc3v3_sys
[ 0.665557] LDO_REG1: supplied by vcc3v3_sys
[ 0.667088] LDO_REG2: supplied by vcc3v3_sys
[ 0.668515] LDO_REG3: supplied by vcc3v3_sys
[ 0.669916] LDO_REG4: supplied by vcc3v3_sys
[ 0.671323] LDO_REG5: supplied by vcc3v3_sys
[ 0.673042] LDO_REG6: supplied by vcc3v3_sys
[ 0.674456] LDO_REG7: supplied by vcc3v3_sys
[ 0.675884] LDO_REG8: supplied by vcc3v3_sys
[ 0.677293] SWITCH_REG1: supplied by vcc3v3_sys
[ 0.678053] SWITCH_REG2: supplied by vcc3v3_sys
[ 0.681886] rk808-rtc rk808-rtc: rtc core: registered rk808-rtc as rtc0
[ 0.682913] rk3x-i2c ff3c0000.i2c: Initialized RK3xxx I2C bus at ffffff80093f8000
[ 0.684314] rk3x-i2c ff110000.i2c: Initialized RK3xxx I2C bus at ffffff80093fa000
[ 0.685066] rockchip-pinctrl pinctrl: pin gpio4-17 already requested by ff940000.hdmi; cannot claim for ff130000.i2c
[ 0.686002] rockchip-pinctrl pinctrl: pin-145 (ff130000.i2c) status -22
[ 0.686606] rockchip-pinctrl pinctrl: could not request pin 145 (gpio4-17) from group i2c3-xfer on device rockchip-pinctrl
[ 0.687594] rk3x-i2c ff130000.i2c: Error applying setting, reverse things back
[ 0.688619] rk3x-i2c ff130000.i2c: Initialized RK3xxx I2C bus at ffffff80093fc000
[ 0.690436] fusb302 4-0022: Can’t get property of role, set role to default DRP
[ 0.694363] fusb302 4-0022: port 0 probe success with role ROLE_MODE_DRP, try_role ROLE_MODE_NONE
[ 0.695314] input: Typec_Headphone as /devices/platform/ff3d0000.i2c/i2c-4/4-0022/input/input0
[ 0.696306] rk3x-i2c ff3d0000.i2c: Initialized RK3xxx I2C bus at ffffff80093fe000
[ 0.698109] IR NEC protocol handler initialized
[ 0.699261] usbcore: registered new interface driver npu_acm
[ 0.699835] usbcore: registered new interface driver uvcvideo
[ 0.700345] USB Video Class driver (1.1.1)
[ 0.701362] rockchip-iodomain ff320000.syscon:io-domains: pmu1830 supplied by 3000000 uV
[ 0.702268] rockchip-iodomain ff770000.syscon:io-domains: bt656 supplied by 1800000 uV
[ 0.703050] rockchip-iodomain ff770000.syscon:io-domains: audio supplied by 1800000 uV
[ 0.703817] rockchip-iodomain ff770000.syscon:io-domains: sdmmc supplied by 3000000 uV
[ 0.704581] rockchip-iodomain ff770000.syscon:io-domains: gpio1830 supplied by 3000000 uV
[ 0.706086] Boot mode: coldboot
[ 0.707564] rockchip-thermal ff260000.tsadc: tsadc is probed successfully!
[ 0.708791] dw_wdt ff848000.watchdog: Should better to setup a ‘resets’ property in dt, that must been named with reset
[ 0.710000] Bluetooth: Virtual HCI driver ver 1.5
[ 0.710566] Bluetooth: HCI UART driver ver 2.3
[ 0.710965] Bluetooth: HCI UART protocol H4 registered
[ 0.711418] Bluetooth: HCI UART protocol LL registered
[ 0.711887] Bluetooth: HCI UART protocol ATH3K registered
[ 0.712422] usbcore: registered new interface driver bfusb
[ 0.712974] usbcore: registered new interface driver btusb
[ 0.713939] cpu cpu0: bin=1
[ 0.714249] cpu cpu0: leakage=22
[ 0.726585] cpu cpu0: temp=29375, pvtm=142548 (143928 + -1380)
[ 0.727292] cpu cpu0: pvtm-volt-sel=0
[ 0.727689] cpu cpu0: bin-scale=34
[ 0.728287] cpu cpu4: bin=1
[ 0.728642] cpu cpu4: leakage=39
[ 0.728982] cpu cpu4: Failed to get reg
[ 0.729328] cpu cpu4: bin-scale=17
[ 0.730662] cpu cpu0: avs=0
[ 0.731020] cpu cpu0: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[ 0.731977] cpu cpu0: failed to find power_model node
[ 0.732844] cpu cpu4: Failed to set regulator for cpu4: -517
[ 0.733611] cpu cpu5: Failed to set regulator for cpu5: -517
[ 0.734870] sdhci: Secure Digital Host Controller Interface driver
[ 0.735415] sdhci: Copyright© Pierre Ossman
[ 0.735936] Synopsys Designware Multimedia Card Interface Driver
[ 0.737330] dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mode.
[ 0.738044] dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller.
[ 0.738673] dwmmc_rockchip fe310000.dwmmc: Version ID is 270a
[ 0.739222] dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 25,32 bit host data width,256 deep fifo
[ 0.740179] dwmmc_rockchip fe310000.dwmmc: No vmmc regulator found
[ 0.740736] dwmmc_rockchip fe310000.dwmmc: No vqmmc regulator found
[ 0.742163] dwmmc_rockchip fe320000.dwmmc: IDMAC supports 32-bit address mode.
[ 0.742879] dwmmc_rockchip fe320000.dwmmc: Using internal DMA controller.
[ 0.743503] dwmmc_rockchip fe320000.dwmmc: Version ID is 270a
[ 0.744053] dwmmc_rockchip fe320000.dwmmc: DW MMC controller at irq 26,32 bit host data width,256 deep fifo
[ 0.745034] dwmmc_rockchip fe320000.dwmmc: No vmmc regulator found
[ 0.745860] vcc_sd: unsupportable voltage range: 3300000-3000000uV
[ 0.746419] rockchip-iodomain ff770000.syscon:io-domains: Setting to 3000000 done
[ 0.747096] rockchip-iodomain ff770000.syscon:io-domains: Setting to 3000000 done
[ 0.760328] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[ 0.773917] dwmmc_rockchip fe320000.dwmmc: 1 slots initialized
[ 0.774877] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.777258] sdhci-arasan fe330000.sdhci: No vmmc regulator found
[ 0.777808] sdhci-arasan fe330000.sdhci: No vqmmc r
[ 0.822620] Initializing XFRM netlink socket
[ 0.823667] NET: Registered protocol family 10
[ 0.825013] NET: Registered protocol family 17
[ 0.825434] NET: Registered protocol family 15
[ 0.826085] Bluetooth: RFCOMM socket layer initialized
[ 0.826585] Bluetooth: RFCOMM ver 1.11
[ 0.826957] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 0.827497] Bluetooth: HIDP socket layer initialized
[ 0.828019] [WLAN_RFKILL]: Enter rfkill_wlan_init
[ 0.828741] [WLAN_RFKILL]: Enter rfkill_wlan_probe
[ 0.829231] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6354
[ 0.829852] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
[ 0.830477] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
[ 0.831214] [WLAN_RFKILL]: wlan_platdata_parse_dt: get property: WIFI,host_wake_irq = 3, flags = 0.
[ 0.832166] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk not found !
[ 0.832893] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
[ 0.833361] [WLAN_RFKILL]: Exit rfkill_wlan_probe
[ 0.833874] [BT_RFKILL]: Enter rfkill_rk_init
[ 0.834721] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 83.
[ 0.835474] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 9.
[ 0.836211] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 90.
[ 0.836941] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 4.
[ 0.837695] [BT_RFKILL]: bluetooth_platdata_parse_dt: clk_get failed!!!.
[ 0.838341] [BT_RFKILL]: Request irq for bt wakeup host
[ 0.838862] [BT_RFKILL]: ** disable irq
[ 0.839330] [BT_RFKILL]: bt_default device registered.
[ 0.839857] Key type dns_resolver registered
[ 0.841390] Registered cp15_barrier emulation handler
[ 0.842072] Registered setend emulation handler
[ 0.843584] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[ 0.844975] mmc0: new high speed SDHC card at address aaaa
[ 0.845734] Loading compiled-in X.509 certificates
[ 0.846656] mmcblk0: mmc0:aaaa SD32G 29.7 GiB
[ 0.848569] rga2: Driver loaded successfully ver:3.2.18218
[ 0.849380] rga2: Module initialized.
[ 0.852407] phy phy-ff770000.syscon:usb2-phy@e450.7: Failed to get VBUS supply regulator
[ 0.855054] mmcblk0: p1 p2 p3 p4 p5
[ 0.857256] mali ff9a0000.gpu: Failed to get regulator
[ 0.857761] mali ff9a0000.gpu: Power control initialization failed
[ 0.864704] xhci-hcd xhci-hcd.7.auto: xHCI Host Controller
[ 0.865396] xhci-hcd xhci-hcd.7.auto: new USB bus registered, assigned bus number 3
[ 0.866297] xhci-hcd xhci-hcd.7.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x06030010
[ 0.867100] xhci-hcd xhci-hcd.7.auto: irq 229, io mem 0xfe800000
[ 0.867821] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.868417] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.869074] usb usb3: Product: xHCI Host Controller
[ 0.869520] usb usb3: Manufacturer: Linux 4.4.194 xhci-hcd
[ 0.870003] usb usb3: SerialNumber: xhci-hcd.7.auto
[ 0.870876] hub 3-0:1.0: USB hub found
[ 0.871232] hub 3-0:1.0: 1 port detected
[ 0.871835] xhci-hcd xhci-hcd.7.auto: xHCI Host Controller
[ 0.872503] xhci-hcd xhci-hcd.7.auto: new USB bus registered, assigned bus number 4
[ 0.873223] usb usb4: We don’t know the algorithms for LPM for this host, disabling LPM.
[ 0.874015] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[ 0.874620] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.875260] usb usb4: Product: xHCI Host Controller
[ 0.875704] usb usb4: Manufacturer: Linux 4.4.194 xhci-hcd
[ 0.876187] usb usb4: SerialNumber: xhci-hcd.7.auto
[ 0.877153] hub 4-0:1.0: USB hub found
[ 0.877539] hub 4-0:1.0: 1 port detected
[
[ 0.970940] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.971618] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.972258] usb usb3: Product: Generic Platform OHCI controller
[ 0.972794] usb usb3: Manufacturer: Linux 4.4.194 ohci_hcd
[ 0.973277] usb usb3: SerialNumber: fe3a0000.usb
[ 0.974582] hub 3-0:1.0: USB hub found
[ 0.974952] hub 3-0:1.0: 1 port detected
[ 0.976482] dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mode.
[ 0.977231] dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller.
[ 0.977843] dwmmc_rockchip fe310000.dwmmc: Version ID is 270a
[ 0.978369] dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 25,32 bit host data width,256 deep fifo
[ 0.979314] dwmmc_rockchip fe310000.dwmmc: No vmmc regulator found
[ 0.979876] dwmmc_rockchip fe310000.dwmmc: No vqmmc regulator found
[ 0.980752] dwmmc_rockchip fe310000.dwmmc: allocated mmc-pwrseq
[ 0.994733] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[ 1.008281] dwmmc_rockchip fe310000.dwmmc: 1 slots initialized
[ 1.011906] asoc-simple-card hdmi-codec: i2s-hifi <-> ff8a0000.i2s mapping ok
[ 1.013750] rockchip-spdif ff870000.spdif: Missing dma channel for stream: 0
[ 1.014379] rockchip-spdif ff870000.spdif: ASoC: pcm constructor failed: -22
[ 1.015032] asoc-simple-card spdif-sound: ASoC: can’t create pcm ff870000.spdif-dit-hifi :-22
[ 1.015795] asoc-simple-card spdif-sound: ASoC: failed to instantiate card -22
[ 1.016602] asoc-simple-card: probe of spdif-sound failed with error -22
[ 1.017571] mali ff9a0000.gpu: Failed to get regulator
[ 1.018026] mali ff9a0000.gpu: Power control initialization failed
[ 1.020805] input: gpio-keys as /devices/platform/gpio-keys/input/input1
[ 1.022273] mali ff9a0000.gpu: Failed to get regulator
[ 1.022755] mali ff9a0000.gpu: Power control initialization failed
[ 1.023349] rk808-rtc rk808-rtc: setting system clock to 2013-01-18 08:50:07 UTC (1358499007)
[ 1.033207] mmc_host mmc2: Bus speed (slot 0) = 300000Hz (slot req 300000Hz, actual 300000HZ div = 0)
[ 1.042349] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 413; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is ‘’, rk_ko_ver is ‘5’, built at ‘10:56:24’, on ‘Oct 21 2022’.
[ 1.044425] Mali: Mali device driver loaded
[ 1.045447] ALSA device list:
[ 1.045731] #0: HDMI-CODEC
[ 1.073404] mmc_host mmc2: Bus speed (slot 0) = 200000Hz (slot req 200000Hz, actual 200000HZ div = 0)
[ 1.119011] mmc_host mmc2: Bus speed (slot 0) = 100000Hz (slot req 100000Hz, actual 100000HZ div = 0)
[ 1.542727] phy phy-ff770000.syscon:usb2-phy@e450.7: charger = USB_FLOATING_CHARGER
[ 1.754026] EXT4-fs (mmcblk0p5): recovery complete
[ 1.755533] EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts: (null)
[ 1.756320] VFS: Mounted root (ext4 filesystem) on device 179:5.
[ 1.757673] devtmpfs: mounted
[ 1.758857] Freeing unused kernel memory: 1024K
[ 2.307440] systemd[1]: System time before build time, advancing clock.
[ 2.326373] systemd[1]: Failed to look up module alias ‘autofs4’: Function not implemented
[ 2.334727] cgroup: cgroup2: unknown option “nsdelegate”
[ 2.351108] systemd[1]: systemd 245.4-4ubuntu3.18 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=hybrid)
[ 2.353856] systemd[1]: Detected architecture arm64.

Welcome to Ubuntu 20.04.1 LTS!

[ 2.363631] systemd[1]: Set hostname to <localhost.localdomain>.
[ 2.810198] random: systemd: uninitialized urandom read (16 bytes read, 68 bits of entropy available)
[ 2.811235] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling.
[ 2.812335] systemd[1]: (This warning is only shown for the first unit using IP firewalling.)
[ 2.814274] systemd[1]: Created slice system-getty.slice.
[ OK ] Created slice system-getty.slice.
[ 2.815167] random: systemd: uninitialized urandom read (16 bytes read, 68 bits of entropy available)
[ 2.816964] systemd[1]: Created slice system-modprobe.slice.
[ OK ] Created slice system-modprobe.slice.
[ 2.817726] random: systemd: uninitialized urandom read (16 bytes read, 68 bits of entropy available)
[ 2.819471] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ OK ] Created slice system-serial\x2dgetty.slice.
[ 2.820319] random: systemd: uninitialized urandom read (16 bytes read, 68 bits of entropy available)
[ 2.821985] systemd[1]: Created slice User and Session Slice.
[ OK ] Created slice User and Session Slice.
[ 2.822766] random: systemd: uninitialized urandom read (16 bytes read, 68 bits of entropy available)
[ 2.824134] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ OK ] Started Dispatch Password …ts to Console Directory Watch.
[ 2.825249] random: systemd: uninitialized urandom read (16 bytes read, 68 bits of entropy available)
[ 2.826645] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ OK ] Started Forward Password R…uests to Wall Directory Watch.
[ 2.827742] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped.
[ 2.829167] random: systemd: uninitialized urandom read (16 bytes read, 68 bits of entropy available)
[ 2.830029] systemd[1]: Reached target Local Encrypted Volumes.
[ OK ] Reached target Local Encrypted Volumes.
[ 2.830790] random: systemd: uninitialized urandom read (16 bytes read, 68 bits of entropy available)
[ 2.832013] systemd[1]: Reached target Paths.
[ OK ] Reached target Paths.
[ 2.832568] random: systemd: uninitialized urandom read (16 bytes read, 68 bits of entropy available)
[ 2.833720] systemd[1]: Reached target Remote File Systems.
[ OK ] Reached target Remote File Systems.
[ 2.834368] random: systemd: uninitialized urandom read (16 bytes read, 68 bits of entropy available)
[ 2.835619] systemd[1]: Reached target Slices.
[ OK ] Reached target Slices.
[ 2.836193] systemd[1]: Reached target Swap.
[ OK ] Reached target Swap.
[ 2.837300] systemd[1]: Listening on initctl Compatibility Named Pipe.
[ OK ] Listening on initctl Compatibility Named Pipe.
[ 2.849963] systemd[1]: Condition check resulted in Journal Audit Socket being skipped.
[ 2.851194] systemd[1]: Listening on Journal Socket (/dev/log).
[ OK ] Listening on Journal Socket (/dev/log).
[ 2.852374] systemd[1]: Listening on Journal Socket.
[ OK ] Listening on Journal Socket.
[ 2.853446] systemd[1]: Listening on udev Control Socket.
[ OK ] Listening on udev Control Socket.
[ 2.854365] systemd[1]: Listening on udev Kernel Socket.
[ OK ] Listening on udev Kernel Socket.
[ 2.855547] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
[ 2.856558] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped.
[ 2.859724] systemd[1]: Mounting Kernel Debug File System…
Mounting Kernel Debug File System…
[ 2.863153] systemd[1]: Mounting Kernel Trace File System…
Mounting Kernel Trace File System…
[ 2.867478] systemd[1]: Starting Journal Service…
Starting Journal Service…
[ 2.868369] systemd[1]: Condition check resulted in Create list of static device nodes for the current kernel being skipped.
[ 2.872251] systemd[1]: Starting Load Kernel Module chromeos_pstore…
Starting Load Kernel Module chromeos_pstore…
[ 2.873176] systemd[1]: Condition check resulted in Load Kernel Module drm being skipped.
[ 2.876674] systemd[1]: Starting Load Kernel Module efi_pstore…
Starting Load Kernel Module efi_pstore…
[ 2.880132] systemd[1]: Starting Load Kernel Module pstore_blk…
Starting Load Kernel Module pstore_blk…
[ 2.883919] systemd[1]: Starting Load Kernel Module pstore_zone…
Starting Load Kernel Module pstore_zone…
[ 2.884906] systemd[1]: Condition check resulted in Load Kernel Module ramoops being skipped.
[ 2.888453] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[ 2.894701] systemd[1]: Starting Load Kernel Modules…
Starting Load Kernel Modules…
[ 2.898763] systemd[1]: Starting Remount Root and Kernel File Systems…
Starting Remount Root and Kernel File Systems…
[ 2.902519] systemd[1]: Starting udev Coldplug all Devices…
Starting udev Coldplug all Devices…
[ 2.906504] systemd[1]: modprobe@chromeos_pstore.service: Succeeded.
[ 2.908833] systemd[1]: Finished Load Kernel Module chromeos_pstore.
[ OK ] Finished Load Kernel Module chromeos_pstore.
[ 2.919989] systemd[1]: modprobe@efi_pstore.service: Succeeded.
[ 2.920971] systemd[1]: Finished Load Kernel Module efi_pstore.
[ OK ] Finished Load Kernel Module efi_pstore.
[ 2.922874] systemd[1]: modprobe@pstore_blk.service: Succeeded.
[ 2.924301] systemd[1]: Finished Load Kernel Module pstore_blk.
[ OK ] Finished Load Kernel Module pstore_blk.
[ 2.926035] systemd[1]: modprobe@pstore_zone.service: Succeeded.
[ 2.927186] systemd[1]: Finished Load Kernel Module pstore_zone.
[ OK ] Finished Load Kernel Module pstore_zone.
[ 2.929101] systemd[1]: Finished Load Kernel Modules.
[ OK ] Finished Load Kernel Modules.
[ 2.931735] systemd[1]: Finished Remount Root and Kernel File Systems.
[ OK ] Finished Remount Root and Kernel File Systems.
[ 2.935643] systemd[1]: Mounting FUSE Control File System…
Mounting FUSE Control File System…
[ 2.940110] systemd[1]: Mounting Kernel Configuration File System…
Mounting Kernel Configuration File System…
[ 2.953746] systemd[1]: Starting Rebuild Hardware Database…
Starting Rebuild Hardware Database…
[ 2.954714] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped.
[ 2.958834] systemd[1]: Starting Load/Save Random Seed…
Starting Load/Save Random Seed…
[ 2.962405] systemd[1]: Starting Apply Kernel Variables…
Starting Apply Kernel Variables…
[ 2.967297] systemd[1]: Starting Create System Users…
Starting Create System Users…
[ 2.974546] systemd[1]: Mounted Kernel Debug File System.
[ OK ] Mounted Kernel Debug File System.
[ 2.975684] systemd[1]: Mounted Kernel Trace File System.
[ OK ] Mounted Kernel Trace File System.
[ 2.977048] systemd[1]: Mounted FUSE Control File System.
[ OK ] Mounted FUSE Control File System.
[ 2.978219] systemd[1]: Mounted Kernel Configuration File System.
[ OK ] Mounted Kernel Configuration File System.
[ OK ] Finished Apply Kernel Variables.
[ OK ] Finished Create System Users.
Starting Create Static Device Nodes in /dev…
[ OK ] Finished Create Static Device Nodes in /dev.
[ OK ] Reached target Local File Systems (Pre).
[ OK ] Reached target Local File Systems.
[ OK ] Finished udev Coldplug all Devices.
[ OK ] Started Journal Service.
Starting Flush Journal to Persistent Storage…
[ OK ] Finished Flush Journal to Persistent Storage.
Starting Create Volatile Files and Directories…
[ OK ] Finished Create Volatile Files and Directories.
Starting Network Name Resolution…
Starting Network Time Synchronization…
Starting Update UTMP about System Boot/Shutdown…
[ OK ] Finished Update UTMP about System Boot/Shutdown.
[ OK ] Started Network Time Synchronization.
[ OK ] Reached target System Time Set.
[ OK ] Reached target System Time Synchronized.
[ OK ] Started Network Name Resolution.
[ OK ] Reached target Host and Network Name Lookups.
[FAILED] Failed to start Rebuild Hardware Database.
See ‘systemctl status systemd-hwdb-update.service’ for details.
Starting udev Kernel Device Manager…
[ OK ] Started udev Kernel Device Manager.
[ OK ] Reached target System Initialization.
[ OK ] Started Daily apt download activities.
[ OK ] Started Daily apt upgrade and clean activities.
[ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems.
[ OK ] Started Discard unused blocks once a week.
[ OK ] Started Message of the Day.
[ OK ] Started Daily Cleanup of Temporary Directories.
[ OK ] Reached target Timers.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ OK ] Reached target Sockets.
[ OK ] Reached target Basic System.
[ OK ] Started D-Bus System Message Bus.
Starting Remove Stale Onli…t4 Metadata Check Snapshots…
Starting Dispatcher daemon for systemd-networkd…
[ OK ] Started Set the CPU Frequency Scaling governor.
[FAILED] Failed to start Login Service.
See ‘systemctl status systemd-logind.service’ for details.
Starting Permit User Sessions…
[ OK ] Stopped Login Service.
[FAILED] Failed to start Login Service.
See ‘systemctl status systemd-logind.service’ for details.
[ OK ] Stopped Login Service.
[FAILED] Failed to start Login Service.
See ‘systemctl status systemd-logind.service’ for details.
[ OK ] Stopped Login Service.
[FAILED] Failed to start Login Service.
See ‘systemctl status systemd-logind.service’ for details.
[ OK ] Stopped Login Service.
[FAILED] Failed to start Login Service.
See ‘systemctl status systemd-logind.service’ for details.
[ OK ] Stopped Login Service.
[FAILED] Failed to start Login Service.
See ‘systemctl status systemd-logind.service’ for details.
[ OK ] Finished Permit User Sessions.
[ OK ] Started Getty on tty1.
[ OK ] Found device /dev/ttyFIQ0.
[ OK ] Reached target Sound Card.
[ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch.
[ OK ] Started Serial Getty on ttyFIQ0.
[ OK ] Reached target Login Prompts.
Starting Load/Save RF Kill Switch Status…
[FAILED] Failed to start Load/Save RF Kill Switch Status.
See ‘systemctl status systemd-rfkill.service’ for details.
Starting Load/Save RF Kill Switch Status…
[FAILED] Failed to start Load/Save RF Kill Switch Status.
See ‘systemctl status systemd-rfkill.service’ for details.
Starting Load/Save RF Kill Switch Status…
[FAILED] Failed to start Load/Save RF Kill Switch Status.
See ‘systemctl status systemd-rfkill.service’ for details.
Starting Load/Save RF Kill Switch Status…
[FAILED] Failed to start Load/Save RF Kill Switch Status.
See ‘systemctl status systemd-rfkill.service’ for details.
Starting Load/Save RF Kill Switch Status…
[FAILED] Failed to start Load/Save RF Kill Switch Status.
See ‘systemctl status systemd-rfkill.service’ for details.
[FAILED] Failed to start Load/Save RF Kill Switch Status.
See ‘systemctl status systemd-rfkill.service’ for details.
[ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots.
[ OK ] Finished Load/Save Random Seed.
[ OK ] Started Dispatcher daemon for systemd-networkd.
[ OK ] Reached target Multi-User System.
Starting Update UTMP about System Runlevel Changes…
[ OK ] Finished Update UTMP about System Runlevel Changes.

Ubuntu 20.04.1 LTS localhost.localdomain ttyFIQ0

localhost login: